Southerly 35RS for sale

Itchenor, United Kingdom

$135,775USD
Listed price £110,000 GBP

General information
Make/model
Southerly 35RS
Category
Used sail boat for sale
Price
$135,775 USD | Listed price £110,000 GBP
Name of boat
ROSA DI VENTI
Year
2006
Length overall
35'5"
Length waterline
30'2"
Beam
11'8"
Draft
7'1"
Displacement
7.69 tons (U.S.)
Keel
Lifting Keel
Location
Itchenor, United Kingdom

About this Southerly 35RS

English

The established features of the Southerly sets very high standard of performance and comfort which appeals to family and cruising yachtsmen alike. The plumb bow and fast lines of the Rob Humphrey's hull, combined with the twin rudder configuration, provides powerful windward performance, and makes the Southerly 35RS a fun and easy yacht to sail.

Dimensions

Length overall: 10.82M

Length waterline: 9.22M

Beam: 3.57M

Draft, Keel up: 0.72M

Draft, Keel down: 2.18M

Displacement: 6,980 Kgs

Total Ballast: 3,255 Kgs

Air Draft: 16.50M

Construction

Hull:

Heavy duty GRP moulding, hand laid up to Northshore's Nordseal laminating system, incorporating multi Axial and unidirectional reinforcements. Thickness increases progressively towards the keel area. The keel box in an integral part of the hull lay-up and sandwich construction stiffening runs the entire length of the hull topsides. All main bulkheads are bonded into the hull at the main layup stage.

Hull Topsides: Southerly Blue gelcoat. Hull was professionally painted with Dupont 2K two part system during summer of 2016

Underwater area: Clear gelcoat

Bootop line: Ivory white gelcoat

Styleline stripes: Ivory White vinyl

Antifouling: Coppercoat

Deck:

Hand laid up GRP sandwich type construction using balsa core stiffening, with plywood in high stress areas where fitting are positioned. Heavily stressed areas are additionally reinforced with unidirectional glass reinforcement. The deck is bonded to the hull through the entire length and to all the main bulkheads resulting in a strong and integrated unit.

Deck: Ivory White gelcoat

Teak capping rail to hull to deck joint upstand

Moulded two tone non-slip finish in bisuit to ring decks

Access to chain locker from foredeck

Swing Keel:

The fixed ballast is an iron casting which acts as the grounding plate and as transverse stiffening for the keel unit. It is fitted into a recess in the hull in the area of the keel box with stainless steel bolts. The aerofoil swing keel is cast iron and incorporates a stainless steel pivot at the leading edge. The swing keel is raised and lowered by a hydraulic ram powered by an electrically driven pump with a hand operated back-up. All hydraulics are easily accessible for maintenance. There is a keel control and gauge showing keel position fitted at the cockpit helm position. A removeable stainless steel pin is used to enable the keel to be locked in the "up" position.

 

Engine

Yanmar 3YM30F 30Hp 3 cylinder, fresh water cooled, diesel engine

Reduction/reverse gear

80 amp alternator

Bronze stern tube with water lubricated stern gland

Stainless steel propeller shaft

Bronze three bladed propeller

Substantial skeg fitted on centreline to protect prop and rudders when dried out

Stainless steel fuel tank under cabin sole below chart table, capacity 182 litres (40 gallons) with sediment trap and line filter

Non metallic water strainer with removable filter

12 volt electric ventilator

Sound deadening to engine box

Hinge up panels at either end of engine box for access

Engine box can be completely removed for maintenance

HRP automatic fire extinguisher in engine compartment

3 x 22L Diesel fuel containers

Thruster

Lewmar 185TT bow thruster 3Kw 55kg thrust with joystock control mounted at steering pedestal

Engineering

Mikuni hot air heating system with three outlets to saloon, forward cabin and aft cabin.

Holding tank system, heads pumps to sea or to tank.

Electrics

12 volt system

Five heavy duty batteries, charged from the engine alternator, one 110Ah sealed lead acid for engine starting, three 110Ah Victron AGM for domestic use (new 2019) and one 110Ah Victron AGM + Ctek charger for Bow thruster

Sterling battery management panel, four position indicator that reads volts and amps

Sterling shore-power charger

Sterling smart alternator regulator

Isolating switches

240V ring main with 5 double UK sockets, and earth leak circuit breaker. With cable and plug for shore power connection plus 2 extension cables

Galvanic isolator with warning lights on switch panel

240V 1Kw immersion heater fitted to calorifier

6 fixed 12V fans, 2 in each cabin

LED Cabin lighting throughout

Reading lights over bunks

Chart light over navigation table

Full navigation light system incorporating bow light, stern light, LED Lopo masthead tri-colour light with all round white anchor light, deck flood light and steaming light. Port, starboard and stern lights all fitted with Searolf LED bulbs

Circuit breakers on main switch panel

Bilge water alarm

300W Inverter plus 3 dedicated UK standard 240V sockets

12v and USB charging sockets in fore cabin and navigation station

Automatic LED lighting in cupboards

Navigation and electronics

Echomax radar reflector fitted at mast

Raymarine ST60+ speed, depth and wind indicators mounted at companionway

Raymarine autopilot with Mamba drive, ST6000+ displays in cockpit and at chart table

Raymarine autopilot remote control

Simad RS35 VHF radio with DSC and AIS reciever

Simrad HS35 Wireless handsets with powered holders in companionway and binnacle

E80 Chart plotter mounted in Navpod at steering pedestal

E80 PC interface at chart table

Navionics Gold electronic chart

18" Raymarine Raydome mounted on gantry

Raystar 125 GPS satellite differential mounted at pushpit

Furuno NX300 Navtex receiver at Navigation station

Domestic radio/hifi with speakers

Water systems and pumps

Pressurised hot and cold water systems

Mixer tap to galley sink

 

Electric emergency pump at sink able to pump seawater or fresh water

Mixer tap in heads compartment

Non-metallic water tank, under forward end of dinette, capacity 205 Litre

Additional flexible tank, capacity 100L

1 x 30L % 1 x 15Lwater bottles

Hot water provided by an engine calorifier unit

Electric sump pump to shower tray

One manual bilge pump

Two electric submersible bilge pump

Deck shower with hot and cold water fitted in cockpit

Steering

Semi-balanced twin rudders

Pedestal mounted 40" stainless steel cockpit wheel with polyester corded covered rim

Lewmar/Whitlock Cobra steering system

Single lever engine control at cockpit helm pedestal

Emergency steering system

6" main steering compass with compass guard

Spars and Rigging

Selden fractional rig

Double swept back spreaders

Selden anodised aluminium spars finish in silver

Internal halyards

1x19 stainless steel wire standing rigging with swage toggle/fork rigging screws

Backstay with manual tensioner

Self tacking jib

Furlex headsail reefing system

Single line reefing led aft to cockpit for mainsail

Single line 1st and 2nd reefs. Third reef ( 2 lines) available in boom and mast but currently unused

Kicker with strong gas insert

Main halyard

Topping lift

Kicker, main halyard, topping lift, outhaul, jib sheet and 2 reefs led aft. Main downhaul German mainsheet led back to port and starboard winches. Track on coachroof.

Genoa halyard at mast

Burgee and signal halyards

Sail controls led aft across pilothouse

Lewmar size 8 winch on mast

Two folding steps fitted at base of mast

Stainless steel bowsprit for gennaker

Fittings on mast and deck for emergency foresail

Walder boom brake with warp, turning blocks and clutches

Sails

 

Furling self tacking jib

Fully battened Sobstad mainsail with Selden MDS mast slides

Code 0 (nearly new) on Rollgen

Brand new mainsail stackpack cover complete with 3 part lazy jacks

Cockpit

Aft cockpit

Self draining

Laid teak to cockpit seats

Laid teak to cockpit sole

Good access aft for boarding through transom

Telescopic stern boarding ladder

Large cockpit locker to port

Gas bottle storage in cockpit locker to starboard

Cave locker in starboard cockpit coaming

Perspex main companionway hatch with washboard

Stainless steel security locking bar to companionway hatch

Instrument panel above hatchway

Brand new sprayhood with zipped centre panel in Tan canvas

Brand new bimini in Tan canvas

Canvas cockpit enclosure

Boom tent

Cockpit mosquito net

Two winch handle pockets

Steering pedestal

Folding teak cockpit table and shelf

Two safety harness eyes

Deck shower with hot and cold water

Deck fittings and loose gear

Cleats forward and aft raised

Spring cleats amidships with stainless steel chafe guard

Stainless steel stemhead fitting with twin bow rollers

GRP foredeck anchor locker with reinforced shelf for windlass

Stainless steel pulpit incorporating navigation light bracket

Stainless steel stanchions and guardwires, with gates port and starboard

Stainless steel pushpit incorporating stern gate & navigation light bracket

Ensign halyard rigged to backstay

Fuel and water deck fillers

Holding tank pump out fitting

Self tacking foresail track with sheet to cockpit

Turning blocks to take reefing lines

Mainsheet track forward of sprayhood with control lines led aft to cockpit

Rope clutches to port and starboard for running rigging

Two Lewmar 40ST winches mounted at end of coaming

Stainless steel grab handles either side of coachroof

Webbing lifelines port and starboard

Stainless steel radar arch gantry incorporated into pushpit

2 x Rigid 80W solar panels mounted on gantry with Solara MPPT controller

Eclectic Energy D400 wind generator (Not currently on board, but heeds remounting having been recently serviced)

Bow mounted LED spotlight

Lewmar H2 12V 1000W electric windlass mounted in anchor locker. With Quick hand held remote and manual switch fitted to helm pedestal

20Kg Spade anchor mounted on "The Twist" self righting shackle

75 Metres of 8mm chain (new 2016) marked every 10M with coloured markers & key

 

Stainless steel anchor recovery hook

Anchor snubber

Buoy snagging hook

100M 16mm Nylon line +60M floating Polypropylene line for Med mooring

Various lengths of mooring warp

2 Swiss-Tec rope rat guards

8mm chain loops for tying to concrete or rock

Electric horn

High power 12V portable spotlight

Stainless steel holder for Fortress kedge anchor welded to pushpit

Fortress kedge anchor with warp and chain in locker, and stemhead fitting

Delta emergency anchor (Unused) in deep stowage 

Para anchor for emergency use in deep stowage

2 Rond anchors (Rusty but serviceable) for inland waterways side-to mooring

Anchor/deck wash pump (Small)

Small fortess anchor and warp for dinghy

Outboard motor bracket mounted on pushpit

Transom mounted snap davits and two gantry mounted 4:1 blocks for dinghy stowage at sea.

Inflatable dinghy (Poor condition)

Jackstays port and starbord

Canvas winch covers

2 Lewmar winch handles, 1 x one touch and 1 x conventional

Re-chargeable electric winch converter

Ocean Safety hermetically sealed 4 man Liferaft with pulpit mounting bracket (annual service due)

Two fire extinguishers

One fire blanket

Nine fenders, 6 tubular, 3 balloon

One fender step (poor condition)

Fender pockets for mounting on pushpit

2 PVC hull protection blankets (almost new)

One motoring cone

One anchor ball

Large plastic flares box and grab bag

Two electronic red flares, one fan-laser, one LED

Passerelle

Boat hook

Ensign and staff

Gas bottles, 2 x 19Kg Camping Gaz and 1 x Greek cylinder

Electrical gas shut off valve in gas locker

3 x 22 Litre spare fuel cans (all full)

5 hoses and extra Hozelock fittings

Hand operated Mangle (Laundry wringer) plus pulpit mounting board

Mop

Deck cleaning brush

Various padlocks and cables

Many boat specific spare parts

Windows, hatches and ventilation

Size 60 opening deck hatch over forecabin. two size 00 opening hatches to galley and heads. Two size 20 opening hatches to saloon and navigation area

Two size 1 glazed opening ports in cockpit to serve aft cabin

Two dorade ventilators on deck serving saloon and navigation area

Ventilator "Tent" for fore cabin deck hatch

Fixed ventilator to heads

Perspex main companionway hatch

Pilot house windows and hull ports are partially reflective toughened glass, bonded into recesses in the GRP mouldings

Internal Joinery and Upholstery

Internal joinery is finished in solid American cherry and faced marine quality plywood. Linings are fabric covered or GRP as appropriate

Galley worktops in Natural acrylic stone "Confetti"

Heads countertop in Nordstone "White"

Cabin soles are teak striped non-slip laminate

Saloon upholstery in Alcantara "Bohemian Blue"

Sleeping cabins upholstered in "Electric Blue"

Curtains in blue

Oceanair sun shades/mosquito nets fitted to three deck hatches

Ikea bed slats under berths

Accommodation

There are a total of five berths with two in the forecabin, two in the aft cabin and one in the saloon. Plus an additional pipe-cot in the forecabin

Galley:

Galley area forward to starboard

Twin stainless steel sinks

Sink top chopping board

Hot and cold pressurised water

Emergency fresh/sea water pump and sink outlet

Worktop in Natural Acrylic Stone: Confetti

Front loading stainless steel refrigerator, Frigoboat VFC90IMOBGR 90L with keel cooler (New 2015)

Stainless steel grab rail to cooker

Fully gimballed SMEV gas cooker with three burners, grill and oven (Fail safe devices on all burners)

Gas cut off tap

Pan stowage locker surrounding mast step

Large opening locker

Two lockers

Two drawers

Cutlery, crockery & miscellaneous kitchen utensils

Kettle for gas hob

Bulkhead mounted clock and kitchen timer

Bulkhead mounted spice rack

Wastebin in dedicated locker

Two overhead lights

Opening Hatch

Fixed hull port

Raised Saloon:

Raised seating arrangement to port, which coverts to a single sea berth with lee cloth

Excellent vision

Stowage under

Stowage outboard

Folding pedestal table

Overhead lights

Opening hatch

Navigation Area:

Chart table to starboard with excellent visibility

Instrument console forward of chart table

Chart stowage

Book stowage below

Navigators seat with back/head rest

Large stowage under seat

Chart light

Main switch panel

Overhead deck light

Opening hatch

Wet hanging locker aft

Aft Cabin:

Large double berth offset to starboard

Large hanging locker to port

Large vanity unit to port with angles Perspex doors, stowage under and outboard

Shelf

Three drawers

Hanging locker to starboard

Stowage drawer under forward end of double berth

240V socket

Two reading lights

Two overhead lights

Two fixed hull ports

Two opening ports to cockpit

Access aft through bulkhead to steering gear

Service access to port

Curtains

Tool locker approximate 2M³ fully shelved

Heads:

Heads compartment forward and to port

Manually operated Lavac Popular marine toilet, with black water holding tank and sea/tank "Y" valve

Hinged seat to cover marine toilet

Washbasin with Nordstone GRP surround in white

Shower head/mixer tap

Stainless steel grab handle

Hot and cold pressurised water

Stowage under and outboard with perspex doors

 

Electric shower pump

Grating to shower tray

Mirror

Toothbrush racks

Fixed portlight

Opening hatch

Waterproof toilet roll holder

Fixed ventilator

Forecabin:

"V" berth, two long single berths, with infill cushion to covert to double berth.

Pipe cot on port side

Large hanging locker

Large shelved locker

Two full length shelves

Storage below berths

Two fixed hull ports

Opening hatch

Curtains

Reading lights

240V and USB sockets

12V fans

Clock

Additional items:

Book shelf racking on cupbard tops

Hidden security cubby hole

Shelving for tool storage

Large marine first aid kit

Netting centred washboard

 

The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice.

Read more

Propulsion
Engine
1 x Yanmar 3YM30F
Fuel
Diesel
Fuel capacity
48 gallons (U.S.)
Accommodation
Number of cabins
2
Number of berths
5

The company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information not warrant the condition if the vessel. A buyer shoudl instruct his agents, or his surveyors, to invstigate such details as trhe buyer desires validated. The vessel is offered subject to prior sale, price change, or withdrawal without notice.

This Southerly 35RS has been viewed 222 times
Broker/Dealer Information

Northshore Shipyard Ltd.

Itchenor Shipyard
Itchenor, Chichester
West Sussex
PO20 7AY
United Kingdom
Please mention that you saw this boat on TheYachtMarket.
XXXX XXX XXX
ABYA Logo
ABYA YACHT BROKER

Setting the standards in yacht broking and conveyancing since 1912

Find out more

Thank you

Your message has been sent.

Ask for more photos

Email to a friend

Report this boat

Thank you, your message has been sent

Why not register your interest in these similar boats?

We will send the following details to the sellers of the selected boats: Your name, email address, phone number (if provided). your country and which boat(s) you are interested in.

Request More Information

Change units of measure

This feature requires cookies to be enabled on your browser.

Show price in:
Show lengths, beam and draft in:
Show displacement or weight in:
Show capacity or volume in:
Show speed in:
Show distance in: